Technical Specifications Programming the Programmable Outlets We recommend that you take the time to read this manual to take full advantage of the many features of your UPS U ninterruptible P ower S ystem. Before installing Pulsar , please read the booklet on the required safety instructions. Then follow the indications in this manual. To discover the entire range of MGE Office Protection Systems products and the options available for the Pulsar range, we invite you to visit our web site at www.
To improve waste treatment and facilitate recycling, separate the various packing components. Packing materials are recyclable and bear the appropriate identification symbol. MGE Office Protection Systems will process products at the end of their service life in compliance with local regulations. MGE Office Protection Systems works with companies in charge of collecting and eliminating our products at the end of their service life.
Dismantling and destruction must take place in compliance with all local regulations concerning waste. At the end of its service life, the product must be transported to a processing center for electrical and electronic waste. The product contains lead-acid batteries that must be processed according to applicable local regulations concerning batteries.
The battery may be removed and disposed of in compliance with correct local disposal regulations. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Recycling symbols are printed on the packing materials to facilitate sorting. Follow steps 1 to 4 for module mounting on the rails.
When the status is active, the contact between the common Pin 4 and the relevant information pin is closed. Connect the UPS socket 9 to the AC-power source using the power cable from the equipments to be protected.
The cable and the connectors are marked in red. Connect the UPS socket 9 to the AC power source using the power cable from the equipments to be protected. It is preferable to connect the priority loads to the outlets marked 8 and the non-priority loads to the outlets marked 7 that can be programmed in pairs 1 and 2.
The UPS charges the battery as soon as it is connected to the AC-power source, even if button 27 is not pressed. LED 20 is ON. During normal operation, the scroll button 25 may be used to read UPS measurements AC input voltage, operating mode, battery capacity and UPS serial number.
If UPS personalization is desired, it is advised to enter the personalization mode at this time. Transfer Transfer to to battery battery power. The necessary energy is provided by the battery. The remaining battery power is low. Shut down all applications on the connected equipment because automatic UPS shutdown is imminent. Following an outage, the UPS restarts automatically when AC power returns unless the restart function was disabled via UPS personalization and the load is again supplied.
Restarting the UPS requires manual intervention. These functions are obtained by opening a contact connected between the appropriate pins of connector 5 on the rear panel of the UPS see diagram on following page. Check the UPS is shut down and the electrical supply network disconnected. Remove connector 5 by unfitting the screws. To return to normal operation, deactivate the external remote shut down contact and restart the UPS using button Plug connector 5 into the back of the UPS.
Connect and restart the UPS according to the previously described procedures. Activate the external remote shut down contact to test the function. Press the scroll button 25 to access any status conditions and alarms, then the measurements for voltage, current, frequency, power output and battery backup time.
Press the scroll button 25 several times until the personalization menu is reached. Press the Enter button 26 to access the different possibilities. Finally, confirm the selection by pressing the Enter button 26 again. Detailed comments are available in the Personal Solution-Pac software. On the first navigation screen, select "Point to Point solution" and follow the instructions on how to install the. Use the escape button 24 to stop the audio alarm. The battery can cause electrocution and high short-circuit currents.
The following safety cautions are required before servicing the battery components:. Remove watches, rings, bracelets and all other metal objects from the hands and arms. C Disconnect the battery block by separating the two connectors never pull on the wires. G Pull the plastic tab to remove the battery block and replace it. B Disconnect the battery block by separating the two connectors never pull on the wires. C Remove the 4 fixing screws on the metal protection cover of the battery.
Take care to firmly press together the two parts of the connector during remounting. Repeat step 3 for each programmable outlet. To configure the powershare to power off at the same time as the main outlets:. Technical questions? If you encounter a problem while following the instructions in this manual, or have questions. To insure that your questions are correctly answered, please obtain the part number, assembly number, and serial number of the unit and include them in any discussions or correspondence.
Time during which the load can be supplied by the UPS operating on battery power. Battery discharge beyond the permissible limit, resulting in irreversible damage to the battery.
Module with UPS outlets for installation in a bay. There are different modules with different. UPS manual-bypass module for maintenance. Previous Page. Next Page. Chapters English 6 Deutsch Mge ups system power supply installation and user manual pulsar ellipse , , , , , pulsar ellipse premium , , , 16 pages.
Mge ups systems installation and user manual pulsar extreme cla c 30 pages. Mge pulsar ups system models esv 8, 11, 14, 22, eb 22, eb 22xla user manual 44 pages.
Page 4 Pulsar Evolution at the end of its service life. Page 5 Foreword Using this document Information may be found in two ways, using: the contents; the index. Pictograms Important instructions that must always be followed. Information, advice, help. Visual indication. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off. Page 6: Table Of Contents Tower models Page 7 Contents Maintenance Trouble-shooting Page 8: Presentation x Page 9: Back 1. Presentation 1.
RS communications port. Data-line protection. Slot for communications-card option. Outlets for direct connection of protected equipment. Programmable outlets 1 and 2. Input circuit-breaker. Page Control Panel 1. Operation on battery power. UPS fault. Battery fault. Group 1 programmable outlets supplied with power.
Group 2 programmable outlets supplied with power. Booster or fader mode. Bargraph indicating percent load at output. Bargraph indicating the battery charge level. Page Unpacking And Parts Check 2. Installation 2. RS communications cable. USB communications cable. Product documentation. Page Rack Models 2. Installation Rack models Two cords for connection of the protected equipment. Telescopic rails for mounting in 19" bay with mounting hardware. Securing system for equipment power cords. Page Tower Models 2.
End of backup time Sleep mode Personalisation optional Replacement of the battery module Technical characteristics Simplified diagram Operating conditions Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. EX Measures that have made Pulsar EX a reference in environmental protection include: the eco-design approach used in product development; recycling of Pulsar EX at the end of its service life. To avoid accidents, the directives listed below must be observed: Never burn the battery risk of explosion. Comply with all applicable regulations for the disposal of the battery. Product safety UPSs must be connected to a nearby wall outlet that is easily accessible.
Never install the UPS near liquids or in an excessively damp environment. Never let a foreign body penetrate inside the UPS. Never block the ventilation grates of the UPS. Never expose the UPS to direct sunlight or a source of heat.
Special precautions The UPS connection instructions contained in this manual must be followed in the indicated order. Prior to handling the battery: remove all watches, rings, bracelets and any other metal objects; use tools with insulated handles.
Foreword Using this document Information may be found primarily by consulting: the contents, the index. Pictograms Important instructions that must always be followed.
0コメント